• <li id="q72mj"></li>

  • <button id="q72mj"></button>
    <i id="q72mj"></i>

      <li id="q72mj"><b id="q72mj"><samp id="q72mj"></samp></b></li>

      <li id="q72mj"><ol id="q72mj"><object id="q72mj"></object></ol></li><button id="q72mj"><label id="q72mj"><mark id="q72mj"></mark></label></button>

      <th id="q72mj"></th>
      LANGUAGE:
      EN RU CN
      RU

      HOME PRODUCTS HVDC & FACTS FACTS

      SERVICES NEWS EVENT CALENDOR CONTACT US
      PCS-9583 Static Synchronous Compensator
    1. The Static Synchronous Compensator is a voltage regulating device based on voltage source converters. It acts as a source or a sink of reactive power which is independent of AC system voltage. The STATCOM can adjust reactive power of power grid, improve power quality, and reduce grid losses and the impact on electrical equipment. It is extensively applied to power grid, renewable energy generation, steel mill, chemical plant, electrified railway, city subway, mine and so on.

    2. Functions System Configuration Operating Principle
      • Power Transmission Substation

      Compensate line reactive power and stabilize system voltage

      Reduce transmission losses

      Increase line transmission capacity through the dynamic support of line terminal voltage

      Improve transient stability to prevent against transient voltage collapse

      Provide power oscillation damping

      • Mining Hoists and Industrial Mills

      Improve power factor, reduce reactive power loss and energy-saving

      Solve serious harmonic pollution problems, and improve power quality by active power filtering

      Enhance line terminal voltage, improve voltage stability and power supply security

      Reduce voltage fluctuation and flickers caused by heavy load during startup

      • Electrified Railway

      Provide power factor control to reduce power loss

      Supply voltage regulation to weak grid

      Compensate negative sequence/unbalance current or voltage

      Provide harmonic filtering

      • Wind Farm and Solar Energy

      Correct system power factor

      Reduce voltage fluctuation and flicker

      Filter harmonic current

      Balance three phase power

      Enhance voltage stability and improve low-voltage ride through (LVRT) capability

      • Steel Plant and Rolling Mill

      Provide harmonic filtering

      Compensate unbalanced voltage

      Significantly reduce voltage fluctuation and flicker

      Improve productivity

      Reduce reactive power impact

      Control power factor

      This complete set of STATCOM system mainly includes the following main equipments:

      • Interface Reactor/Converter Transformer

      The interface reactor/converter transformer is used to connect the converter with the AC power networks, realizing the active power and reactive power exchange between the converter and the AC power networks.

      • Startup Equipment

      To start the STATCOM system, the capacitor at DC side needs to be charged firstly. And for reducing the charging current and the impact on the system, the startup equipment is adopted in STATCOM system.

      • Power Valve

      Power module, as the basic unit of STATCOM system, consists of IGBT and its drive circuit, supporting capacitor, radiator, equalizing resistance and so on. The power valves adopt H-bridge cascaded structure. Each phase consists of a number of power modules, adopting redundant design and satisfying “N-1” or “N-2” operational requirements.

      • Cooling System

      Formation of enormous heat during operation may damage the components if it is not dissipated well. During low system capacity, PCS-9583 STATCOM adopts forced air cooling whereas during large system capacity, it adopts closed-loop water cooling with specialized control system.

      • STATCOM Control and Protection System

      The STATCOM control and protection system consists of PCS-9583 PCP (Pole Control and Protection), PCS-9589 VBC (Valve base Control) unit, SMC (Sub-module controller), interposing relay set, network switch and other protection devices.

      PCS-9583 STATCOM system adopts voltage source converter and the most advanced reactive power compensation technology, not needing large-capacity capacitors and inductors. The H-bridge circuit is connected to the grid via connection transformer or reactor, by suitably adjusting the phase angle and amplitude of output voltage at AC side of the bridged circuit or directly controlling its AC current, this circuit can absorb or generate reactive current as required and realize dynamic adjustment of voltage or reactive power.

      The cascading scheme of multi-level topology is used in the PCS- 9583 STATCOM system. This topology consists of several H-bridge power units with monopole multiplier modulation to achieve three-level output on the AC side. Each phase adopts the carrier phase modulation method to obtain better voltage output waveform with much more level numbers.The cascading scheme can output phase voltage with 2N +1 levels if each phase comprises N +1 links (i.e. the H-bridge power unit).

      Previous:PCS-9580 Static Var Compensator Next:PCS-9570 Series Compensation Back to list

      ? Copyright NR Electric Co., Ltd.
      2001-2020. All Rights Reserved.

      About us Service & Support Company Training Contact Us

      Solutions Power Generation Transmission System Distribution Network Industrial Consumer

      Products Protection,Automation&Control FACTS HVDC Renewable & Microgrid

      亚洲男人最新版本天堂_2020AV天堂网手机在线观看_东北少妇和黑人3p视频_大香伊蕉国产av
    3. <li id="q72mj"></li>

    4. <button id="q72mj"></button>
      <i id="q72mj"></i>

        <li id="q72mj"><b id="q72mj"><samp id="q72mj"></samp></b></li>

        <li id="q72mj"><ol id="q72mj"><object id="q72mj"></object></ol></li><button id="q72mj"><label id="q72mj"><mark id="q72mj"></mark></label></button>

        <th id="q72mj"></th>